* Estimated delivery times start from the date of shipment, excluding processing time.
* Actual delivery times may vary due to holidays, weather conditions, or customs delays.
Two-way VI curve tester, which can display two-way waveforms at the same time, which is convenient for comparison.
4 levels of internal resistance adjustable, 4 test frequencies, can be used when connected to an oscilloscope, both analog oscilloscopes and digital oscilloscopes can be used
Oscilloscope parameter setting:
*. Adjust the oscilloscope to X-Y mode(different oscilloscopes have different adjustment methods, please explore by yourself)
* Adjust the vertical parameters of the 2 channels of X Y to 1V/div, and only one of the single-track oscilloscopes needs to be adjusted. ,
*The analog oscilloscope does not need to adjust the time base, the digital oscilloscope time base is adjusted between 1-5ms
*After the connection is correct, the oscilloscope will display a horizontal line. If a vertical line is displayed, the xY plug will be reversed.
*Adjust the vertical and horizontal parameters, the horizontal and vertical lines are in the display box.
Method of connecting analog oscilloscope:
The analog oscilloscope connection is relatively simple, and different oscilloscopes are slightly different.
Adjust the oscilloscope to xY mode. Some oscilloscopes can be selected by pressing the buttons, while others are selected by the knob to xY mode. Please study by yourself.
Connect the BNC cable to the oscilloscope and power on. Normally, a horizontal line will be displayed. Adjust the xY vertical channel parameters, about 1V/div, and then adjust the x Y attenuation so that the horizontal line is in the display frame. It can also pass the VI test version. The x attenuation potentiometer on the upper side can assist in adjusting the length of the horizontal line. If the test pen iis short-circuited, a vertical line will be displayed under normal circumstances. If the vertical line is too long or too short, you need to adjust the Y channel parameters to make the vertical line in the display frame. Half grid or 1 grid to the edge is better. If the horizontal and vertical lines are normal, you can enter the normal measurement.
How to connect a digital oscilloscope:
For digital oscilloscopes, enter the xY mode through the menu or keys. The two channels of xY are adjusted to 1V/div,and the single-track oscilloscope only needs to adjust the Y channel. Adjust the time base to 1-5 milliseconds. The xY channel selects DC coupling, and the
attenuation is 1x.
When the oscilloscope is not connected, the screen should be a bright spot. Adjust the horizontal and vertical to center the bright spot. Connect the VI tester. Normally, it should be a horizontal line. Adjust the 103 potentiometer at the top of the VI board to make the horizontal line in the display frame. , Half a grid or 1 grid to the edge is
better. Short-circuit the test leads, and the display should be a vertical line at this time. Adjust the Y channel parameters so that the vertical line is in the display frame. So far, debugging is basically over.
When testing the circuit board online, do not charge the circuit board. If there is a large capacitor on the circuit board, discharge the capacitor first, otherwise it is easy to burn out the VI test board.
Funciona perfectamente y llegó el envío en perfectas condiciones. Es el complemento ideal de todos los que tenemos un osciloscopio, para comprobar los componentes de una placa de circuitos y sus componentes electrónicos defectuosos.
It works perfectly and the shipment arrived in perfect condition. It is the ideal complement to all of us who have an oscilloscope, to check the components of a circuit board and its defective electronic components.
It works perfectly and the shipment arrived in perfect condition. It is the ideal complement to all of us who have an oscilloscope, to check the components of a circuit board and its defective electronic components.
I was a bit unhappy at first as I was not able to download the manual and my unit arrived with a cracked case. I began to investigate it and repair it. The instructions available on the sales page provided enough information to set the unit up and running some tests. The unit works better than I had expected. I was able to determine the frequencies used. Low = 62 Hz Med = 234 Hz Med 2 = 2 kHz and High = 14.5 kHz. The red knob selects one of 4 different internal resistances. The A/B push button turns on and off the dual channel mode so that you can easily compare one circuit board position to another. The Blue knob adjusts the position of the "B" Channel image on the scope screen. I added a power switch to the unit so that it could be left plugged in when I wanted to. I also added some English Labels and non-slip feet for the back so that it doesn't slide around on the bench. The only item I have not been able to identify is a Blue Jack on the front that is labeled "G" on the front and "T" on the internal board. If anyone has figured what the "G" Jack is please let me know. I wrote a complaint to Banggood about the inability to down load the Manual and about a week later they sent me the pdf file. Unfortunately it did not identify the "G" jack. Over All I am very pleased with the unit and the way it functions. I would recommend it to anyone who has a curiosity about curve tracers and a scope capable of X-Y operation.
I was a bit unhappy at first as I was not able to download the manual and my unit arrived with a cracked case. I began to investigate it and repair it. The instructions available on the sales page provided enough information to set the unit up and running some tests. The unit works better than I had expected. I was able to determine the frequencies used. Low = 62 Hz Med = 234 Hz Med 2 = 2 kHz and High = 14.5 kHz. The red knob selects one of 4 different internal resistances. The A/B push button turns on and off the dual channel mode so that you can easily compare one circuit board position to another. The Blue knob adjusts the position of the "B" Channel image on the scope screen. I added a power switch to the unit so that it could be left plugged in when I wanted to. I also added some English Labels and non-slip feet for the back so that it doesn't slide around on the bench. The only item I have not been able to identify is a Blue Jack on the front that is labeled "G" on the front and "T" on the internal board. If anyone has figured what the "G" Jack is please let me know. I wrote a complaint to Banggood about the inability to down load the Manual and about a week later they sent me the pdf file. Unfortunately it did not identify the "G" jack. Over All I am very pleased with the unit and the way it functions. I would recommend it to anyone who has a curiosity about curve tracers and a scope capable of X-Y operation.
I was a bit unhappy at first as I was not able to download the manual and my unit arrived with a cracked case. I began to investigate it and repair it. The instructions available on the sales page provided enough information to set the unit up and running some tests. The unit works better than I had expected. I was able to determine the frequencies used. Low = 62 Hz Med = 234 Hz Med 2 = 2 kHz and High = 14.5 kHz. The red knob selects one of 4 different internal resistances. The A/B push button turns on and off the dual channel mode so that you can easily compare one circuit board position to another. The Blue knob adjusts the position of the "B" Channel image on the scope screen. I added a power switch to the unit so that it could be left plugged in when I wanted to. I also added some English Labels and non-slip feet for the back so that it doesn't slide around on the bench. The only item I have not been able to identify is a Blue Jack on the front that is labeled "G" on the front and "T" on the internal board. If anyone has figured what the "G" Jack is please let me know. I wrote a complaint to Banggood about the inability to down load the Manual and about a week later they sent me the pdf file. Unfortunately it did not identify the "G" jack. Over All I am very pleased with the unit and the way it functions. I would recommend it to anyone who has a curiosity about curve tracers and a scope capable of X-Y operation.
Tips:For questions about your order, place of delivery, product discount, taxation, delivery time, warranty, shipping, payment, exchange rate, and other questions unrelated to the product, please contact customer service.
showing 1-19 of 19|
Show Original
A part of the QA has been auto-translated.
0
Q:
or greetings you can see the graphics on some monitor let's say see the images of the elements to test grasias
ola saludos puede uno ver los gráficos en alg ún monitor digamos ver las imágenes delos elementos a probar grasias
Je ne sais pas s'il y a un adaptateur français ou non, mais l'adaptateur que j'ai reçu est de 24 volts 0.50Amps. La partie intérieure du connecteur est +, l'extérieur est -. ~5.5(?) mm OD, ~2,5-3(?) mm ID... J'espère que cela vous aidera d'une façon ou d'une autre. À votre santé!
Je ne sais pas s'il y a un adaptateur français ou non, mais l'adaptateur que j'ai reçu est de 24 volts 0.50Amps. La partie intérieure du connecteur est +, l'extérieur est -. ~5.5(?) mm OD, ~2,5-3(?) mm ID... J'espère que cela vous aidera d'une façon ou d'une autre. À votre santé!
Answered by NH_4X4JEEP on 17/03/2023Helpful (0)
0
Q:
I bought type 3 and in the orders is type 2. Please send type 3 otherwise cancel the order. Thank you.
Eu comprei o tipo 3 e nos pedidos está o tipo 2. Por favor envie o tipo 3 caso contrario cancele o pedido. Obrigado.
Hello friends, you can consult online customer service
Hello friends, you can consult online customer service
Answered by The seller on 25/03/2022Helpful (0)
0
Q:
I would like to get a more detailed manual of the equipment. I see two potentiometers and two resistive trimmers and it is not clear how they have to be set. A manual and a schematic diagram is what you need to properly operate the item. When I click on the english manual, I do not get anything.
I would like to get a more detailed manual of the equipment. I see two potentiometers and two resistive trimmers and it is not clear how they have to be set. A manual and a schematic diagram is what you need to properly operate the item. When I click on the english manual, I do not get anything.
Hello friends, if you need product manuals, you can consult customer service, they will provide you with
Hello friends, if you need product manuals, you can consult customer service, they will provide you with
Answered by The seller on 09/02/2022Helpful (0)
0
Q:
thank you for your answer but ı don't undersent clearly ı want to learn Test voltage and test frequency (forexample : low 5V, mid*****V, mid*****V high 50v and Frequency: 10Hz, 100Hz, 500Hz, 2kHz etc.)
thank you for your answer but ı don't undersent clearly ı want to learn Test voltage and test frequency (forexample : low 5V, mid*****V, mid*****V high 50v and Frequency: 10Hz, 100Hz, 500Hz, 2kHz etc.)
Hello friends, if you have any questions about the product, you can consult the online customer service, or ask the customer service for a manual
Hello friends, if you have any questions about the product, you can consult the online customer service, or ask the customer service for a manual
Answered by The seller on 17/01/2022Helpful (0)
0
Q:
How many voltages do low, medium1, medium2, and high levels?
Test frequencies up to how many gigahertz?
Is it done with the impedance test technique during the test?
How many voltages do low, medium1, medium2, and high levels?
Test frequencies up to how many gigahertz?
Is it done with the impedance test technique during the test?